Tourniquet holder for MOLLE, a belt or a wall

The tourniquet comes out one-handed with an upward pull, yet does not fall out when you run. Each holder fits a specific model, with no metal, screws or glue; volunteers get a lower price from 10 pieces.

Order a MOLLE holder — 150 UAH All versions and prices

Versions and prices

Price per piece, lower from 10 pieces. Colours: coyote, olive or black; the wall holder is red. Printed to order from 1 day and shipped by Nova Poshta across Ukraine.

For MOLLE
An open cradle for the tourniquet and two straps for PALS webbing. A tooth at the end of each strap hooks the webbing, so the holder does not ride up when you pull the tourniquet.

Size
68 × 49 × 100 mm
Included
for CAT Gen 7, SAM-XT or Sich

150 UAH from 10 pcs — 130 UAH

Order
For a belt
The same cradle with a closed loop at the back: it slides onto an unbuckled belt and then cannot slip or come off.

Size
67 × 53 × 100 mm
Included
for a 38, 45 or 50 mm belt

160 UAH from 10 pcs — 140 UAH

Order
Universal
For units with mixed tourniquets: a V-shaped floor centres a CAT Gen 7, SAM-XT or Sich, and shock cord holds it in place.

Size
78 × 44 × 100 mm
Included
4 mm shock cord

180 UAH from 10 pcs — 160 UAH

Order
Sleeve
The cheapest for batches: a short sleeve on a single MOLLE strap, holding the tourniquet by wall pressure alone.

Size
69 × 49 × 92 mm
Included
for CAT Gen 7

110 UAH from 10 pcs — 95 UAH

Order
Pair for two tourniquets
“One for me, one for a comrade”: two tourniquets on a shared plate, each drawn separately with one hand. Takes four PALS columns.

Size
136 × 49 × 100 mm
Included
for 2 × CAT Gen 7

270 UAH from 10 pcs — 240 UAH

Order
Wall holder
For shelters, schools, offices and vehicles: a red holder with a label above the tourniquet so it is found at a glance. The label text is up to you.

Size
101 × 45 × 226 mm
Included
3 screws with wall plugs

210 UAH from 10 pcs — 190 UAH

Order
Didn’t find your version?
Tell us what you need — we’ll pick one of ours or make one just for you.
- A different size or colour
- Your text, name or logo
- A completely different shape — we’ll model it ourselves
Message us
We reply within an hour during working hours. Modelling is charged separately.

How it holds

The side walls are springs: they are printed curved inwards, and the tourniquet straightens them and gets even pressure from both sides. It comes out upwards with 15–30 N — a one-handed pull, even in gloves: the tourniquet stands about 72 mm proud of the walls. When running and jumping its inertia is several times lower, so it does not creep out, and it cannot pop forwards or sideways — the lips and walls hold it.

Made for a specific tourniquet

The main holder fits the CAT Gen 7, with separate ones for the SAM-XT and Sich, while the universal one takes all three. The belt holder fits a 38, 45 or 50 mm belt. For another tourniquet or belt, measure the folded tourniquet (width and thickness) or the belt and send us the numbers: we will print to them.

For volunteers and units

From 10 pieces the price is lower, and one print run fits 12 MOLLE holders or sleeves on the bed, so batches are identical. Colours: coyote, olive or black. The side wall carries a raised “TQ” mark or your own short text, and the wall holder has a label above the tourniquet, such as the name of the building.

Limitations

PETG is more brittle in frost: do not fit or remove the holder in freezing cold, as a knock against armour or concrete can chip a lip.
PETG softens from about 70 °C: do not leave the holder in a car behind glass in summer. Black heats up most in the sun — coyote or olive is better for summer.
The force is calculated for a new tourniquet. If it sits too tight or too loose, tell us and we will print with a different grip. Check how the tourniquet draws once a season.
At 136 mm wide, the pair will not fit a narrow cummerbund — use two MOLLE holders instead.
The belt holder cannot go on a buckled belt — the belt has to be undone.

Close-up

In section: a strap under two rows of PALS webbing, its tooth hooked on the lower one.

Black, olive and coyote. The walls are printed curved, and the tourniquet straightens them.

Images are renders of the 3D model — this is how the product will look once printed.

FAQ

Which tourniquet does it fit?

The main one fits the CAT Gen 7. There are separate holders for the SAM-XT and Sich, and the universal one fits all three. For another tourniquet we print to its folded dimensions.

Won’t the tourniquet fall out when I run?

No: the walls grip it with several times the force of its inertia when running and jumping, and the lips at the front stop it popping forwards. To draw it, pull upwards.

Can I draw it with one hand?

Yes: the tourniquet stands about 72 mm above the holder, so there is something to grab even in gloves. The force is 15–30 N, that is 1.5–3 kg.

What is the price for volunteers?

From 10 pieces it is lower: the sleeve is 95 UAH, the MOLLE holder 130 UAH and the pair 240 UAH each. For larger batches, tell us the quantity and we will give you a lead time.

Will it survive frost and heat?

PETG works in both frost and heat, but it is more brittle in frost and softens from about 70 °C. Do not fit or remove the holder in freezing cold, and do not leave it in a car behind glass in summer.

Can I have my own label?

Yes: the side wall carries a short mark, “TQ” by default, and the wall holder has a label above the tourniquet, such as the name of the building.

Other products

All ready-made products (40)All 3D printing services

A different tourniquet or belt?

Send us the tourniquet model or its folded dimensions and the belt width — we will print a holder to fit for the same price.

Telegram WhatsApp Fill in the form

Tourniquet holder for MOLLE, a belt or a wall

Versions and prices

For MOLLE

For a belt

Universal

Sleeve

Pair for two tourniquets

Wall holder

Didn’t find your version?